Promega
M3D HomeGithub RepositoryParts Store
  • Welcome!
  • Getting Started
    • Critical Warnings & Information
    • Unboxing & Assembly
    • Check Your Printer
    • Setup Your Electronics
    • Setup Your Network
    • Updating SD Card Structure
    • Getting Started: Where to Go From Here
  • Beginner's Guides
    • Read This First
    • Your Extruder
    • Homing The Printer
    • Get Your Bed Ready
    • Running A Print
    • Common Terminology
  • Advanced Guides
    • Printer Assemblies
    • Printer Coordinates
    • Moving The Motor
    • Introduction To G-Code Commands
    • Meet The Extruder
    • Heating The Bed & Nozzle
    • Loading & Unloading Filament
    • The Bed & Probe
    • Bed Leveling & Probing
    • Tuning The Z Homing Procedure
    • Bypass Bed Leveling (Temporary)
    • Software Layers
    • What is Slicing?
    • Preparing The Print
    • Printing The Print
    • Where To Go From Here
  • Your Printer & Filament Settings
    • Printer Settings (Default)
    • ABS-R Filament
    • PLA Filament
    • Filament Extrusion Rate
    • How To Mix
    • How To Properly Apply Elmer's Glue
  • Documentation
    • Software/Firmware
      • SD Card Structure
      • Updating Firmware
      • Macros
      • Adjust Homing Macros
      • Tool Definitions
      • Duet Driver
    • Electronics
      • The Electrical Standard
      • Duet Maestro Wiring
      • Extruder Assembly Wiring
    • Mechanical Systems
      • Compound Mixing
      • Single K'Tana
  • Repair & Maintenance
    • Install/Uninstall
      • Back Cover
      • Filtration System
      • Cable Chain
      • Extruder
      • Nozzle
      • Limit Switch Holder
        • X Axis
        • Y Axis
        • Z Axis
      • Sliders
      • Belt Clamps
      • CoreXY
      • Fans
    • Routing Z Belts
    • Belt Tensioning
    • Slowing Down Your Bed
    • Mechanical Bed Leveling
    • Z-Probe Calibration & Software Bed Leveling
    • Screw & Tool List
    • Temperature Calibration
    • Unclogging The Nozzle
  • How To Troubleshoot
    • Network Connection
    • Duet Web Console (DWC)
    • Z Probe
    • Mesh Compensation
    • Bed
    • Heater
    • Extruder
    • Homing
    • Common Troubleshooting
      • Help! My Extruders Are Backwards
  • Changelog
  • Your Printer's 3D Parts
    • Latest Parts
      • Frame
      • Extruder System
      • Bed
    • Promega 1.24 or earlier
  • Quad
    • Setup Guide
      • Install
      • Calibration
  • M3D Community
    • Active Community Support
    • How To Contribute
    • Community Guides
      • Ruler Shortcut
    • Community Slicer Settings
    • Add-Ons
      • Modified Printed Parts
      • Gearbox
      • Quad
Powered by GitBook
On this page
  • 1.19: Inception - June 26, 2018
  • 1.20: June 26, 2018
  • 1.21: July 13, 2018
  • 1.23: July 17, 2018
  • 1.24: July 23, 2018
  • 1.25 : July 30, 2018

Changelog

1.19: Inception - June 26, 2018

  • Updated Printed Parts:

    • 051402_C1 Z Top Belt Clamp

    • 051404_B3 Z Bottom Belt Clamp

    • 051168_B2 Y Limit Switch Holder

    • 051166_C1 X Limit Switch Holder

    • 051112_B1 Spool Holder

1.20: June 26, 2018

  • New Z Belt Tightening method:

    • Clamping with a washer

  • Updated Printed Parts:

    • Z Belt Bottoms: REMOVED

    • 051224_A2 Bed Terminal Cover

    • 051172_B2 Bed _ Power Switch Holder

    • 051108_C1 Rear Cable Harness_Base

    • 051134_A2 Rear Cable Harness Support

1.21: July 13, 2018

  • Updated Printed Parts:

  • Updated SD card contents.

  • Updated wire connections (board side)

  • Updated Printed Parts:

    • 051224_A3 Bed Terminal Cover

    • 051108_D1 Rear Cable Harness_Base

    • 058302_B1 Front Cable Harness Base

    • 058304_A1 Front Cable Harness Cover

1.23: July 17, 2018

  • Updated Printed Parts:

    • 051162_B2 Z Limit Switch Holder

    • 051404_A1 Magnet Holder Left

    • 051405_A1 Magnet Holder Right

1.24: July 23, 2018

  • Update Printed Parts:

    • 051176_A2 Bed Limit Slider

    • 051174_A2 Bed Limit Housing

  • Bed Switch Endstop Improvements:

    • Reinforced soldering

    • Longer wire

1.25 : July 30, 2018

  • New public 3D printed part file names.

    • Naming conversion details under:

      • \Public\Printed Part Bin\Conversion Details\Naming Conversion - Details (as of 7/27/201811_37a.m.).pdf

    • A copy of the entire bin before conversion is under:

      • \Public\Printed Part Bin\Conversion Details\Bin (Prior To Naming Conversion)

  • Updated Printed Parts:

    • 058302_B3 Front Cable Harness Base

    • 058302_B3 Front Cable Harness Base_Text

    • 058304_A3 Front Cable Harness Cover

  • Duet3D Hardware Update:

PreviousHelp! My Extruders Are BackwardsNextYour Printer's 3D Parts

Last updated 6 years ago