Promega
M3D HomeGithub RepositoryParts Store
  • Welcome!
  • Getting Started
    • Critical Warnings & Information
    • Unboxing & Assembly
    • Check Your Printer
    • Setup Your Electronics
    • Setup Your Network
    • Updating SD Card Structure
    • Getting Started: Where to Go From Here
  • Beginner's Guides
    • Read This First
    • Your Extruder
    • Homing The Printer
    • Get Your Bed Ready
    • Running A Print
    • Common Terminology
  • Advanced Guides
    • Printer Assemblies
    • Printer Coordinates
    • Moving The Motor
    • Introduction To G-Code Commands
    • Meet The Extruder
    • Heating The Bed & Nozzle
    • Loading & Unloading Filament
    • The Bed & Probe
    • Bed Leveling & Probing
    • Tuning The Z Homing Procedure
    • Bypass Bed Leveling (Temporary)
    • Software Layers
    • What is Slicing?
    • Preparing The Print
    • Printing The Print
    • Where To Go From Here
  • Your Printer & Filament Settings
    • Printer Settings (Default)
    • ABS-R Filament
    • PLA Filament
    • Filament Extrusion Rate
    • How To Mix
    • How To Properly Apply Elmer's Glue
  • Documentation
    • Software/Firmware
      • SD Card Structure
      • Updating Firmware
      • Macros
      • Adjust Homing Macros
      • Tool Definitions
      • Duet Driver
    • Electronics
      • The Electrical Standard
      • Duet Maestro Wiring
      • Extruder Assembly Wiring
    • Mechanical Systems
      • Compound Mixing
      • Single K'Tana
  • Repair & Maintenance
    • Install/Uninstall
      • Back Cover
      • Filtration System
      • Cable Chain
      • Extruder
      • Nozzle
      • Limit Switch Holder
        • X Axis
        • Y Axis
        • Z Axis
      • Sliders
      • Belt Clamps
      • CoreXY
      • Fans
    • Routing Z Belts
    • Belt Tensioning
    • Slowing Down Your Bed
    • Mechanical Bed Leveling
    • Z-Probe Calibration & Software Bed Leveling
    • Screw & Tool List
    • Temperature Calibration
    • Unclogging The Nozzle
  • How To Troubleshoot
    • Network Connection
    • Duet Web Console (DWC)
    • Z Probe
    • Mesh Compensation
    • Bed
    • Heater
    • Extruder
    • Homing
    • Common Troubleshooting
      • Help! My Extruders Are Backwards
  • Changelog
  • Your Printer's 3D Parts
    • Latest Parts
      • Frame
      • Extruder System
      • Bed
    • Promega 1.24 or earlier
  • Quad
    • Setup Guide
      • Install
      • Calibration
  • M3D Community
    • Active Community Support
    • How To Contribute
    • Community Guides
      • Ruler Shortcut
    • Community Slicer Settings
    • Add-Ons
      • Modified Printed Parts
      • Gearbox
      • Quad
Powered by GitBook
On this page
  1. Getting Started

Getting Started: Where to Go From Here

PreviousUpdating SD Card StructureNextBeginner's Guides

Last updated 6 years ago

Now that you have completed the Getting Started guides. You are ready to go. Consider reading the following guides as you learn more about the Promega and its functionalities.

  • : All supported G-code commands

  • : Explanation of the Wiring of the Promega.

  • : How to update the SD card structure.

  • : Learn more about macro files and how they can make your life easier.

  • : The chapter that can fix all your problems (hopefully).

  • : Maintain the printer!

Duet3D G-code Wiki
Duet Maestro Wiring
Updating SD Card Structure
Macros
Repair Guides
Maintenance Guides