Promega
M3D HomeGithub RepositoryParts Store
  • Welcome!
  • Getting Started
    • Critical Warnings & Information
    • Unboxing & Assembly
    • Check Your Printer
    • Setup Your Electronics
    • Setup Your Network
    • Updating SD Card Structure
    • Getting Started: Where to Go From Here
  • Beginner's Guides
    • Read This First
    • Your Extruder
    • Homing The Printer
    • Get Your Bed Ready
    • Running A Print
    • Common Terminology
  • Advanced Guides
    • Printer Assemblies
    • Printer Coordinates
    • Moving The Motor
    • Introduction To G-Code Commands
    • Meet The Extruder
    • Heating The Bed & Nozzle
    • Loading & Unloading Filament
    • The Bed & Probe
    • Bed Leveling & Probing
    • Tuning The Z Homing Procedure
    • Bypass Bed Leveling (Temporary)
    • Software Layers
    • What is Slicing?
    • Preparing The Print
    • Printing The Print
    • Where To Go From Here
  • Your Printer & Filament Settings
    • Printer Settings (Default)
    • ABS-R Filament
    • PLA Filament
    • Filament Extrusion Rate
    • How To Mix
    • How To Properly Apply Elmer's Glue
  • Documentation
    • Software/Firmware
      • SD Card Structure
      • Updating Firmware
      • Macros
      • Adjust Homing Macros
      • Tool Definitions
      • Duet Driver
    • Electronics
      • The Electrical Standard
      • Duet Maestro Wiring
      • Extruder Assembly Wiring
    • Mechanical Systems
      • Compound Mixing
      • Single K'Tana
  • Repair & Maintenance
    • Install/Uninstall
      • Back Cover
      • Filtration System
      • Cable Chain
      • Extruder
      • Nozzle
      • Limit Switch Holder
        • X Axis
        • Y Axis
        • Z Axis
      • Sliders
      • Belt Clamps
      • CoreXY
      • Fans
    • Routing Z Belts
    • Belt Tensioning
    • Slowing Down Your Bed
    • Mechanical Bed Leveling
    • Z-Probe Calibration & Software Bed Leveling
    • Screw & Tool List
    • Temperature Calibration
    • Unclogging The Nozzle
  • How To Troubleshoot
    • Network Connection
    • Duet Web Console (DWC)
    • Z Probe
    • Mesh Compensation
    • Bed
    • Heater
    • Extruder
    • Homing
    • Common Troubleshooting
      • Help! My Extruders Are Backwards
  • Changelog
  • Your Printer's 3D Parts
    • Latest Parts
      • Frame
      • Extruder System
      • Bed
    • Promega 1.24 or earlier
  • Quad
    • Setup Guide
      • Install
      • Calibration
  • M3D Community
    • Active Community Support
    • How To Contribute
    • Community Guides
      • Ruler Shortcut
    • Community Slicer Settings
    • Add-Ons
      • Modified Printed Parts
      • Gearbox
      • Quad
Powered by GitBook
On this page
  • XYZ Calibration
  • Extrusion Calibration
  1. M3D Community
  2. Add-Ons

Quad

PreviousGearbox

Last updated 6 years ago

XYZ Calibration

The XYZ calibration is identical to the Promega calibration process.

Refer to the for information.

Dismiss any reference to the Compound or K'Tana (e.g. "Your Extruder" page)

Extrusion Calibration

Operation of Quad (e.g. loading) is identical to the QuadFusion.

Refer to the for information.

Promega Beginner Guide
QuadFusion Beginner Guide