Promega
M3D HomeGithub RepositoryParts Store
  • Welcome!
  • Getting Started
    • Critical Warnings & Information
    • Unboxing & Assembly
    • Check Your Printer
    • Setup Your Electronics
    • Setup Your Network
    • Updating SD Card Structure
    • Getting Started: Where to Go From Here
  • Beginner's Guides
    • Read This First
    • Your Extruder
    • Homing The Printer
    • Get Your Bed Ready
    • Running A Print
    • Common Terminology
  • Advanced Guides
    • Printer Assemblies
    • Printer Coordinates
    • Moving The Motor
    • Introduction To G-Code Commands
    • Meet The Extruder
    • Heating The Bed & Nozzle
    • Loading & Unloading Filament
    • The Bed & Probe
    • Bed Leveling & Probing
    • Tuning The Z Homing Procedure
    • Bypass Bed Leveling (Temporary)
    • Software Layers
    • What is Slicing?
    • Preparing The Print
    • Printing The Print
    • Where To Go From Here
  • Your Printer & Filament Settings
    • Printer Settings (Default)
    • ABS-R Filament
    • PLA Filament
    • Filament Extrusion Rate
    • How To Mix
    • How To Properly Apply Elmer's Glue
  • Documentation
    • Software/Firmware
      • SD Card Structure
      • Updating Firmware
      • Macros
      • Adjust Homing Macros
      • Tool Definitions
      • Duet Driver
    • Electronics
      • The Electrical Standard
      • Duet Maestro Wiring
      • Extruder Assembly Wiring
    • Mechanical Systems
      • Compound Mixing
      • Single K'Tana
  • Repair & Maintenance
    • Install/Uninstall
      • Back Cover
      • Filtration System
      • Cable Chain
      • Extruder
      • Nozzle
      • Limit Switch Holder
        • X Axis
        • Y Axis
        • Z Axis
      • Sliders
      • Belt Clamps
      • CoreXY
      • Fans
    • Routing Z Belts
    • Belt Tensioning
    • Slowing Down Your Bed
    • Mechanical Bed Leveling
    • Z-Probe Calibration & Software Bed Leveling
    • Screw & Tool List
    • Temperature Calibration
    • Unclogging The Nozzle
  • How To Troubleshoot
    • Network Connection
    • Duet Web Console (DWC)
    • Z Probe
    • Mesh Compensation
    • Bed
    • Heater
    • Extruder
    • Homing
    • Common Troubleshooting
      • Help! My Extruders Are Backwards
  • Changelog
  • Your Printer's 3D Parts
    • Latest Parts
      • Frame
      • Extruder System
      • Bed
    • Promega 1.24 or earlier
  • Quad
    • Setup Guide
      • Install
      • Calibration
  • M3D Community
    • Active Community Support
    • How To Contribute
    • Community Guides
      • Ruler Shortcut
    • Community Slicer Settings
    • Add-Ons
      • Modified Printed Parts
      • Gearbox
      • Quad
Powered by GitBook
On this page
  1. Your Printer & Filament Settings

How To Properly Apply Elmer's Glue

A guide on how to apply Elmer's Glue properly.

Let's begin.

Heat the bed to 70 C.

Wait for the bed to reach temperature.

Lightly apply a THIN layer of Elmer's glue.

The lines applied showed by all consistent (either horizontal, vertical, or diagonal)

Do Not make crazy lines.

Wait for the layer to dry.

The purple tint of the glue will fade away.

Repeat: Apply another THIN layer of Elmer's glue.

You should repeat the THIN layer application until you've done 5 layers.

Thanks to m3rc for figuring this out.

PreviousHow To MixNextDocumentation

Last updated 6 years ago